Back / Home


A Mp3-Player for old Palm OS devices - Part 1/2

First Setup with an Arduino Nano

01.12.2019

This article series deals with equipping an old Palm PDA with an MP3 player. It is not a complicated procedure to keep the effort low, so the PDA serves as a controller and display device for the functions provided by the MP3 module used, a DFPlayer Mini.

For this project I'm using an old Palm m100. Of course from the current point of view, there are only old Palm OS devices. But when I go my first PDA, a m100 with Palm OS 3.5 and a few years later, when Palm OS 5 was released, for me, everything with Palm OS 4 (or lower) was old and everthing with Palm OS 5 was "new". After all, Palm OS 5 had made a good leap at that time: Bluetooth had found its way into most devices, and it was possible to play videos and music on most devices without having to convert them beforehand. Of course, there were some devices that could do this before, but they were relatively rare. Since the old m1xx devices had nearly no multimedia capabilities and the m100 has an easily accessible connector, my choice fell on this one. Besides the m100, I also have a Sony CliƩ N770C/U, a Palm m130, a Sony CliƩ SJ20 and a Handspring Visor Neo to choose from. The N770C already has an Mp3 player, the m130 has a very small connector and the SJ20 has - as far as I've read it here - "no simple serial interface". The Visor was no longer a choice, because I simply made my first attempts with the m100 and the Visor was only added to my collection later.

The m100 is only used as an example, of course this project can be transferred to pretty much any Palm that has a serial interface - and that should be the case with every Palm.

This article doesn't really have much to do with Palm OS, because it creates the base for the Mp3 player project. Instead of connecting everything to a m100 and hoping, that everything is working, I hooked everything up to an Arduino Nano (clone). So this article covers the basics: Communication between an Arduino Nano and a DFPlayer Mini. The choice fell on a DFPlayer Mini, because it can be controlled relatively simply over a serial interface. A disadvantage, however, is that the functions are limited to what the Mp3 module has to offer. For example, there is no direct access to the module's SD card, so you can't list files or jump to a position in a music track.

The DFPlayer Mini

The DFPlayer Mini is a Mp3-Player-Module which can be controlled via a serial interface by sending HEX-values. The datasheet can be found here: DFPlayer Mini Datasheet

All relevant functions are described in the datasheet. But there is one topic, I want to cover here, because it can be a bit tricky.

Data is send in arrays with hex values like this one:

 uint8_t Play[10] = {0x7E,0xFF,0x06,0x03,0x00,0x00,0x01,0xFE,0xF7,0xEF};

Each value represents one property:

  1. "0x7E" => Start-Byte
  2. "0xFF" => Version-Information (always "0xFF")
  3. "0x06" => the number of bytes after "Len", Checksums are not counted
  4. "0x03" => Command
  5. "0x00" => Command feedback, "0x00" no feedback, "0x01" feedback
  6. "0x00" => Argument 1
  7. "0x01" => Argument 2
  8. "0xFE" => Checksum 1 (high data byte)
  9. "0xF7" => Checksum 2 (low data byte)
  10. "0xEF" => End-Byte

Everything is (more or less) self-explanatory, but the datasheet does not cover how the checksum is calculated and had some erroneous checksum-values (or I have another version of the DFPlayer Mini).

The checksum is calculated like this:

  1. Sum up every value from (including) "Version-Information" until (excluding) "Checksum 1"
  2. Convert the result into an decimal value
  3. multiply it by "-1"
  4. Convert the result back into a hex-value, signed 2's complement

With the value aboves it is:

  1. 0xFF+0x06+0x03+0x00+0x00+0x01 = 0x109
  2. 0x109 = 265
  3. 265 * -1 = -265
  4. -265 = 0xFEF7 (as signed 2's complement)

FE
is the high data byte and
F7
is the low data byte.

These tools can help to calculate the checksum manually:

The datasheet (on page 6) is showing the checksum values "FF" and "E6", which were not working for me.

The schematic

The schematic is very simple, because it only as four components:

... and of course some wires. It is setup like shown here:

(Open in a new tab for the full resolution.)

The (very simple) code

The code is as simple as the schematic:

#include "Arduino.h"
#include "SoftwareSerial.h"

SoftwareSerial sSerial(10, 11); // RX, TX
void printDetail(uint8_t type, int value);

void setup()
{

  // Defining Pin 10 and 11 as RX/TX-Pins
  int serial1 = 10; 
  int serial2 = 11;

  // Software Serial is used to communicate with the DFPlayer-Mini
  SoftwareSerial mySerial(serial1, serial2);

  // Very important is the correct baud rate, in this case (with the DFPlayer Mini): 9600 kbps
  mySerial.begin(9600);

  // These values are setting the volume to 10 (of 30)
  uint8_t Volume[10]   = {0x7E,0xFF,0x06,0x06,0x00,0x00,0x0F,0xFF,0xD5,0xEF};

  // These values playing the first file on the Micro-SD-Card
  uint8_t Play[10]     = {0x7E,0xFF,0x06,0x03,0x00,0x00,0x01,0xFE,0xF7,0xEF};

  // Sending the values
  mySerial.write(Volume, 10);
  mySerial.write(Play, 10);
}

void loop()
{
  // Nothing to do here
}

The last two steps are copying a MP3-file on a micro-SD-card (simply in the root-directory), inserting it into the DFPlayer Mini and uploading the code to an Arduino Nano (clone). The song should start playing some seconds after the codeupload has finished.

If you want to build an Arudino-Mp3-Play, have look at this library, which is a helpful wrapper for the DFPlayerMini: DFRobotDFPlayerMini

Of course, the DFPlayer Mini can do more than just adjust the volume and play a song. But in this article I just wanted to show a practical example, which you can extend as you like. In the following the Mp3-Player-Application for a Palm should be able to do more than this article describes.

The next part (2/2) is about connection the Palm m100 to the Mp3-Module:
A Mp3-Player for old Palm OS devices - New hardware for an old Palm m100


Misc